Skip to the page
Cutaway of a water heater tank showing the anode rod

Anode rod water heater replacement: what it is and when to do it

The anode rod is the sacrificial part that protects your tank from rust. This page explains when to check it, how it is replaced and when a new water heater makes more sense.

Request a plumber quote

Fill this in and a local specialist gets back to you to quote.

So the business can look at the job and price it.

  1. Describe the job. A short form, two minutes or so.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. You choose. Go ahead only if the price suits you.

An anode rod is a metal rod, usually magnesium or aluminum, that hangs inside a tank water heater and corrodes in place of the steel tank. Once it is used up, the tank itself starts to rust. Replacing the rod is a small job compared with replacing the heater, and many manuals and plumbers suggest checking it every few years. If the tank is already leaking, a new rod will not help. See the water heater repair plumber page for other faults, or request quotes below.

What does an anode rod do, and how do you know it needs replacing?

The rod is a sacrificial part: water attacks it before it attacks the tank lining. When most of the metal is gone, the tank begins to corrode. Signs include a rod worn thin or coated when inspected, rusty hot water, a rotten-egg smell, popping noises from sediment and a tank that is several years old without a check.

Plumbing guides often suggest inspecting the rod every few years, sooner in hard or aggressive water, though there is no single interval for every tank, so follow your owner's manual. Inspect it by turning off power or gas, closing the cold water valve, relieving pressure, draining a little and unscrewing the rod from the top of the tank. Replace it when it is badly eroded, or bare steel shows along most of its length.

An inspection is also a chance to check the temperature and pressure relief valve and the sediment level. Sediment is covered on the flushing sediment from a water heater page.

How is an anode rod replaced?

The plumber shuts off power or gas and the cold water supply, relieves pressure, drains some water, loosens the rod with a socket (commonly a 1-1/16 inch hex head), removes it, wraps the threads of the new rod with sealing tape, installs it, refills the tank and checks for leaks. Tight clearance above the heater may call for a flexible rod.

A socket wrench on a water heater anode rod head

Common snags: a rod fused into the tank by corrosion, a space too short above the heater for a straight rod and fittings that leak after reassembly. A plumber has an impact wrench and flexible rods for those cases. Do not force the rod if the tank starts to move or leak.

Safety points for a DIY attempt: turn off the electric breaker or set the gas control to off, keep the tank filled when power is on so elements do not burn out, and know where the water main valve is. Anything involving gas piping or the burner needs a California contractor license. California's plumbing classification, C-36, covers installing and replacing water heating equipment and its safety devices.

Which anode rod material should you choose?

Magnesium and aluminum are the common rod materials, and which suits a tank depends on the water, and zinc-aluminum alloys and powered rods are options when water smells of sulfur. Material choice depends on your water and the tank. A plumber can match it to your tank and your symptoms.

If hot water smells like rotten eggs, the rod can be one cause because sulfate reducing bacteria react with the rod. Replacing it with a different type may help, but removing the rod permanently is a bad idea. At least one manufacturer's manual warns that removing it for good can void the warranty, and the tank loses its protection. Ask the plumber about the options.

Your water supplier publishes an annual water quality report that lists minerals, which helps when picking a rod.

What should you do about a water heater pilot light problem?

If the pilot light on a gas water heater goes out, relight it by following the instructions on the label on the heater. If it keeps going out, the usual causes are a worn thermocouple, a dirty pilot orifice, a draft or a failing gas control valve. Repeated outages are a reason to have a plumber look at it.

If you smell gas, do not relight anything. Leave the building, call 911 from outside, then call your gas utility. PG&E's emergency page lists 1-800-743-5000 for PG&E customers. Do not use switches or phones inside.

Gas appliance connections and control valves need a contractor license. A homeowner can relight a pilot per the label but should not repair gas parts.

When is replacing the tank a better choice than replacing the rod?

If the tank is leaking, rusting at the seams or is well beyond its expected years, replacement makes sense. A rod can extend a tank that is in good shape but cannot repair corrosion that has already gone through the wall. Weigh the age, the leak history and the warranty.

A failing tank often shows a puddle, a wet base or rust at the bottom fittings. See water heater leaking and water heater leaking hot water. For the price of the rod job, see anode rod replacement cost, and for a new unit, water heater cost. California requires water heaters to be strapped against earthquake movement, and a replacement commonly needs a permit and inspection, so ask the plumber.

Request quotes for either an inspection or a replacement.

Questions people ask

What is the most common problem with a water heater?

The usual ones are no hot water from a failed element or gas control, a pilot that will not stay lit, sediment noise and leaks as the tank ages. A regular flush and a rod check can prevent some of them. A plumber can diagnose which one you have.

How long does an anode rod replacement take?

For a plumber with access to the top of the tank, it is usually a short visit that includes draining, swapping and refilling. A stuck rod or a tight ceiling adds time. Ask the business for an estimate when you request quotes.

Do I need to be home for an anode rod replacement?

Plan to be home, since water and power or gas are off for part of the visit and someone needs to give access to the heater. If it is in a garage or closet, make sure the area is clear.

How often should I replace the anode rod?

There is no single number. Many guides suggest checking every few years and replacing when it is mostly consumed. Hard or aggressive water uses it up faster. Follow your owner's manual.

Will a new anode rod stop a leak?

No. If water is coming from the tank, the steel has been breached and a rod will not fix that. A rod helps prevent corrosion in a sound tank. A plumber can tell whether a leak is a fitting or the tank itself.

In this section

  • Anode rod replacement prices

    Anode rod replacement by a plumber is typically about $200 to $300, with the rod itself $20 to $50.

  • Flushing sediment from a heater

    How to flush sediment from a tank water heater, what the job involves, when to leave it to a plumber, and how to get quotes from local…

  • Water heater leaking hot water

    Why a water heater leaks, what rumbling, ticking and loud noises mean, what to do when the pilot light or heat fails, and when to call a…

  • Water heater leaking

    A water heater leaking is either a fixable fitting or a failed tank.

Sources

Last changed