Most plumbers bill between $75 and $150 an hour for standard work, and published guides put the full spread at about $45 to $200 depending on experience and the job. Many add a call out fee on top, usually $50 to $300. These are national guides, not Stockton price lists, so treat them as a starting point. When you ask for quotes through Stockton Plumbing Hub, the local plumbing business that visits sets the real price for your job.
Below you will find the rates by experience level, what a normal call out fee looks like, how after-hours work changes the bill, and how to choose between an hourly and a flat quote.
What is a normal plumber hourly rate?
A normal plumber hourly rate is about $75 to $150. One national guide puts the average near $90 an hour and lists a wider range of roughly $45 to $200; another also gives $45 to $200. Rates sit higher for complex work, tight access and busy periods, and lower for simple jobs and smaller businesses.
The hourly figure is only the labor. Parts, a call out fee, permits and any after-hours surcharge are billed separately, so two quotes with the same hourly rate can still land far apart. The tables below show where the ranges come from.
| Rate type | Typical range | Source note |
|---|---|---|
| Most plumbers, standard work | $75 to $150 per hour | Fixr |
| Full published spread | $45 to $200 per hour | Fixr and Bob Vila |
| National average | $90 per hour | Fixr |
| Emergency hourly rate | $150 per hour as a standard | Fixr; Bob Vila says after-hours work often costs time-and-a-half to triple the standard rate |
What do plumbers charge by experience level?
Rates climb with experience: apprentices run roughly $20 to $40 an hour, journeyman plumbers roughly $45 to $90, and master plumbers roughly $70 to $200. An apprentice has to be supervised, so you normally pay the rate of the person sent to lead the job, not the apprentice rate.
A higher rate does not always mean a higher bill. A master plumber who diagnoses a leak in 30 minutes can cost less than a cheaper hand who needs two hours. Ask who is coming and what that person's rate is, then compare the estimated hours as well as the dollars.
What is a normal call out fee for a plumber?
A normal call out fee runs $50 to $300 in one national guide and $100 to $350 in another. One guide splits it by level, with journeyman visits at $50 to $150 and master visits at $150 to $300. The fee covers travel and the first look at the problem, and some plumbers fold it into the hourly rate or waive it when you approve the repair.
Always ask whether the fee is credited toward the work if you go ahead.
What is the average call out charge for a plumber at night or on a weekend?
After-hours work often costs time-and-a-half to triple the standard rate, or a flat fee of $100 to $350 on top of the hourly rate. Another guide describes an emergency call as about $150 an hour, and gives a flat emergency call out fee of $200 to $300.
If the problem can wait until morning, shutting off the water at the main valve and booking a daytime slot can save a large part of that premium. The full picture for night and holiday work is on the emergency plumber cost page.
Why does a plumber bill more than the wages plumbers earn?
The U.S. Bureau of Labor Statistics reports a median pay of $30.67 an hour for plumbers, pipefitters and steamfitters (May 2025). That is what the worker earns, not what the customer pays. The billed rate also has to cover the vehicle, tools, insurance, dispatch, software and the time between jobs.
Published guides list overhead, permits, inspection requirements and callback risk among the factors behind the hourly rate. A business billing $100 an hour is not keeping $100: the gap is the cost of having a fully equipped truck arrive at your door.
Should you choose an hourly quote or a flat price?
Choose a flat price when the work is well defined, such as a toilet swap or a faucet, and choose hourly when the scope is unknown, such as tracing a leak behind a wall. A flat price gives you a ceiling before work starts. Hourly work is fairer when the diagnosis is the job.
Published per-job ranges give a sense of what flat quotes look like for common work. They are national figures for normal business hours.
| Job | Typical range |
|---|---|
| Clearing a clog or snaking a drain | $100 to $500 |
| Burst pipe repair | $200 to $1,000 |
| Toilet installation | $400 to $800 |
| Water heater repair | $150 to $750 |
| Water heater installation | $800 to $2,500 |
| Gas line repair | $150 to $700 |
For deeper pricing on particular jobs, see the water heater cost and slab leak repair cost pages, or the general plumber cost overview. Business customers can read about commercial plumber hourly cost, which runs on a different scale.
How do you check who is sending the quote?
California requires a contractor license from the Contractors State License Board for work valued at $1,000 or more in combined labor and materials, and for any work that needs a building permit, so a larger plumbing job should come from a plumbing business that holds a C-36 license. This site passes on quote requests, and the business that visits is the one holding the license, which any contractor lookup at cslb.ca.gov will confirm.
Look at what the different types of plumbers do if you are not sure which kind of specialist a job needs.